Tricks of the Trade

  • How to look after your Lithium–Ion Batteries

  • In this post I hope to give you a run-down of the customer feedback we get here at ITS regarding Li-ion Power tool batteries, we also have some suggestions as to how to get the most out of them and hopefully make them last longer.

    I suspect that if you’re reading this then you’re one of two types of people. Either you’re looking at the title and thinking “well it’s a battery, you use it, you charge it, you use it again” (and in the style of a well-known Russian Meerkat) “Simples” or possibly you’re someone that has had plenty of trouble in the past with batteries or you’ve heard of friends and colleagues that have had nothing but grief from them and therefore you’re reluctant to spend your hard earned money until you know how best to look after them.

    Well for those of you that are fans of Makita, this video from ITS TV runs through some of the best practises for looking after your batteries.

    Why do my Li-ion Batteries have issues?

    There are two main reasons for lithium batteries to give up the ghost. The first issue is heat. Heat is a battery’s worst enemy, if a battery gets too hot then it’s CPU and fuel cells will burn out, rendering the battery useless and your day on site redundant. Second is over discharge. Over discharge occurs when your battery is on the brink of running out of juice completely and whichever machine you’re using beings to fade. But instead of stopping (and yes we’ve all done it) and charging that battery up you decide to squeeze every single last breath out of the battery and force your way through the job manually.

    This sort of practise may save you time but also it’ll possibly cost you an entire Li-ion battery. Because its completely bled dry it has no power to communicate with its charger the battery won’t be able to gain a charge and you won’t be able to ever use it.
    Dewalt Lithium Batteries

    How do I stop my Lithium battery from getting too hot?

    Now there isn’t really a scientific answer to “how hot is too hot?” for a lithium-ion battery, so I’ll have to leave this one in your hands. Of course pushing your tool beyond its recommended limits, (whether that’s using a massive Auger bit or sawing through reinforced material) is a bad idea. These tools are tested by the manufacturers and the spec sheets are there to tell you what your machine is capable of. Anything you attempt outside those limitations could have a very negative affect on the inside of your tool and moreover your battery. Furthermore if you’re using a machine for a long time continuously or a high drain tool like a jigsaw or circular saw then it’s worth using your judgment to see if your batteries are starting to overheat.

    How to prevent over-discharge on li-ion batteries

    As mentioned above, over discharge happens when you push your batteries to their absolute limits, to the point where it doesn’t have enough power to even communicate with the charger. So it’s pretty obvious that the best way to avoid this from happening is as soon as you feel that your tool/battery is starting to struggle – get it on a charger! Don’t squeeze those extras 10 screws out of it, or cut that last 100mm of timber, just get it out and get it on charge!


    Is Li-ion different to Ni-CD?

    For those veterans amongst you, you’re probably reading the above and thinking that’s its blasphemy and although it wasn’t ever particularly good practise (because the tools weren’t designed to do that) if your power tool battery was starting to run low then plenty of people would walk around site with their fingers on the trigger making sure that you run it down as much as possible before charging. You used to see that sort of thing a lot (although again it certainly isn’t recommended) with Ni-CD because they had a ‘memory for charge’ which meant that whenever you charged it, it created a ‘minimal charge point’ from that exact point. So if the battery had 25% of juice left and you charged it, you’d only ever get the remaining 75% from it thereafter.

    Ni-CD batteries

    Do not fall into the trap of doing that with Li-ion batteries! They work completely differently and you can charge them at any point and they’ll still retain their full charging capacity. So for the sake of 2 mins of swapping your battery out for another one – or even waiting around with a brew for 20 mins while it charges, please make sure you don’t push your battery too far and get it on charge before ruining it forever.

    The future of power tool batteries

    Milwaukee Drill

    Most brands these days are have created ‘fail-safes’ within their tools and batteries so that they don’t actually allow users to over-discharge their batteries by cutting out as soon as the battery beings to struggle. It’s very much the same with heat, the same thing happens if a battery gets too hot, the tool will just shut down and not allow the battery to be used until it has cooled down. These fail safes take that grey area and the choice away from you the consumer, letting you get on with what’s important and what you’re good at.

    Makita Stars on Tools and Batteries

    Makita Battery Star

    To focus on the Makita ‘fail safes’ they have put a chip in their latest tools and batteries. You can tell whether or not your tool/battery has got this chip in because it’s represented by a small ‘star’ engraved into the underside of the battery compartment on a tool, or pictured on the side of your battery. These chips talk to one another and convey exactly what I was talking about above – If the battery is being over worked and therefore getting too hot, it’ll cut all power to the battery. Moreover if the battery is losing power and about to run out of juice, it won’t let you run it flat it’ll just stop all power going to the machine.

    Please note that these fail safes only work this way if BOTH your battery and machine are ‘starred’ products. You may have some existing non-starred batteries and put a starred machine on them, if this is the case then the chip in the machine doesn’t have a corresponding chip to ’talk’ to and so the fail-safe is not in place. The same is true if your battery is a newer ‘starred’ battery but your power tool doesn’t have a star on it.

    If you would like any further information on the Makita Stars or to find out about a particular model no please email us on and we’ll get back to you asap.

    Makita Star

    Hopfully that gives you a good idea of how and why li-ion batteries may fail on you, and what you can do to prevent that from happening.

    If it has been handy then please share it around using the buttons below, and if you have any questions please leave a comment or call 020 8532 5000

    More posts you might like:
    Posted in Tricks of the Trade
    17 comments on “How to look after your Lithium–Ion Batteries
    1. N Desroches says:

      Brilliant piece of information many thanks

    2. steve veasey says:

      just watched the video about looking after batteries I use mine in a radio which stops when the battery is flat, is there a failsafe in the radio to stop over discharge?
      thanks steve

      • Richard Hughes says:

        Hi Steve, do you know what model radio it is?

        I would think that the radio doesn’t have the failsafes in them yet, but you may be in luck because a radio is a very low drain machine and often wont push the battery way beyond its limits.

    3. David salmon says:

      I purchased a cordless makita jig saw about 18 months ago from its tools , last week it just stopped working . If I have the invoice , could I get it replaced ?

    4. Colon Harte says:

      I believe that you shud push a makita 18v li-Lon 3ah to its breaking point and some times beyond to see what they can stand up to or is it only me?

    5. Bob says:

      Due to theft from my van 2 years ago I was left with no Makita cordless tools, so I had to bite the bullet.
      I chose to invest in Panasonic 14.4v cordless tools, it has been the best move I made.
      Their are tough, user friendly, and have the best tool/battery interface I’ve seen so far, heat/battery condition is available to advise when to charge/and heat awareness.
      Best investment I have made.

    6. steve veasey says:

      hi Richard I have a dab job site radio (the black and white one)

    7. Paul loftus says:

      I have about 8 batteries that are dead, is there anything I can do to get them working again ?

      • Richard Hughes says:

        Hi Paul,

        Not really no! – There may be a couple of cowbot videos on the internet that suggests ways to fix batteries etc, but Li-ion technology is very dangerous. Its worth you phoning whoever makes your battery and discussing with them directly.

        Good Luck!

    8. Steve Ingman says:

      I read your blog with interest as there seems to be so many myths regarding all types of batteries. You’re right in that most tradesmen over use there batteries and probably push too far.
      I think the tool makers should consider this and make some sort of quick clip on battery gauge so you can see just what is left.
      I may have 4 or 5 batteries on the go at any one time and keeping track of which is fully charged etc is nigh on impossible, I have purchased the new USB charger from Dewalt which is good but still only shows three bars on the battery scale, a ten bar one would be better.
      Surely all the big manufactures realise that a lot of tradesmen invest serious money in there kit and rely heavily on them to earn a living so a little more thought into how you can take better care of things like the batteries is in everyone’s best interest. ( it’d be interesting to know how many batteries are ruined by over use but are still in warranty and returned for free replacement)

      Anyway, interesting blog, thanks for the info

      • Richard Hughes says:

        Hi Steve,

        Thanks for the comment, its a really good point. Hopefully with this and more and more article around the web etc the brands are sitting up and taking note of exactly what you’re saying. Nobody means to run batteries down totally but like you say it simpossible to keep track of all of them,

        We shall have to wait an see what th enext gen of batteries are like.

    9. Antoine Grujon says:

      This article gives some great advice. I think it is missing some advice on storage though. I had 3 Makita 18v LI batteries which I used sensibly and kept fully charged. However, I’m not a pro and only do occasional DIY. When I tried to use my tools after some time without use (3 or 4 months), 2 of the batteries were showing errors when trying to charge them again. The third battery died about 6 weeks later again having being stored fully charged. How often would you recommend a battery should be given a recharged if it isn’t going to be used regularly. Is ok to store the battery on the power tool.

    10. James dean says:

      I have 4 batteries broken for makita 18v I brought my kit when they were first released but refuse to buy new tools to fit new batteries as I pad over £1000 for my kit is there away to stop batteries getting broken

    11. Brian says:

      I recently bought a deWalt OEM 4Ah slider battery with a red button release instead instead of yellow as with genuine deWalt, and had charging issues from the outset. The battery will only charge for about 10-15 seconds then the charger shuts down. The charger works perfectly fine with my other genuine deWalt batteries and I am beginning to think after reading these pages that there is a incompatability problem with OEM batteries. Lesson learned “buyer beware”.

    12. Martin Harvey says:

      My makita tools are keep in my van or garage so what i need to know is can the cold weather damage them

    Add a Comment

    Your email address will not be published. Required fields are marked *